The 1990 Winnebago Cw822fw has 7 NHTSA recall campaigns affecting an estimated 1,120 vehicles. Recall repairs are always free at any authorized dealer. Last updated July 20, 2026.
THE REAR SHOCK ABSORBER BRACKET CAUSES THE REAR SHOCK ABSORBER LOWER MOUNTING HARDWARE TO FAIL PREMATURELY.
THE REAR SHOCK ABSORBER MAY BECOME DETACHED AND CAUSEDAMAGE TO SURROUNDING COMPONENTS (TIRES, SPRINGS, ETC.) WHICH COULD LEAD TOLOSS OF VEHICLE CONTROL AND AN ACCIDENT.
REMOVE OLD SHOCK ABSORBER MOUNTING BRACKETS, REATTACH NEW BRACKETS TO FRAME, ADAPT SHOCK ABSORBERS AND ADD A JOUNCE PAD SPACER BETWEEN EACH JOUNCE PAD AND THE NEW SHOCK ABSORBER BRACKETS.
ROAD DEBRIS MAY ENTER AN OPENING IN THE REAR SUSPENSION TRAILING ARM AND DAMAGE THE BEARING SEAL.
VEHICLE STABILITY MAY BE IMPAIRED UNDER CERTAIN ROADOR OPERATING CONDITIONS WHICH MAY CAUSE LOSS OF VEHICLE CONTROL.
DRILL A 1/8 INCH VENT/DRAIN HOLE, CLEAN THE BEARING SEAL AREA, APPLY HEAVY WASHOUT RESISTANT GREASE BETWEEN THE HUB ASSEMBLY AND THE TRAILING ARM SURFACES, AND INSTALL A FOAM RUBBER PLUG INTO THE ANGLED OPENING AT INBOARD SIDE OF THE TRAILING ARM.
THE STEERING GEAR MOUNTING BRACKET BOLTS MAY BECOME LOOSE AND ALLOW THE GEAR TO MOVE OUT OF POSITION.
THE STEERING EFFORT INCREASES AND MAY CAUSE LOSS OFSTEERING CONTROL AND A POSSIBLE VEHICLE ACCIDENT.
REPLACE THE MOUNTING BOLTS; PLACE A SPACER PLATE BETWEEN THE STEERING GEAR MOUNTING BRACKET AND THE LEFT FRONT FRAME; REATTACH THE STEERING GEAR ASSEMBLY MOUNTING BRACKET TO THE FRAME USING NEW HARDENED NUTS TORQUED TO 285 FOOT POUNDS.
THE STEERING GEAR INTERMEDIATE SHAFT CLAMPS USED TO RETAIN THE INTERMEDIATE SHAFT TO THE STEERING GEAR SHAFT AND THE COLUMN SHAFT CAN BECOME LOOSE BECAUSE OF INCORRECT BOLT SIZE AND CLAMP FORCE.
LOOSE INTERMEDIATE SHAFT CLAMPS COULD WEAR SMOOTH THERESPECTIVE SPLINES OF EACH CONNECTING PART AND CAUSE THE ASSEMBLY TO FALL APART.THIS RESULTS IN LOSS OF STEERING CONTROL AND A POSSIBLE VEHICLE ACCIDENT.
REPLACE THE PINCH BOLTS IN THE INTERMEDIATE STEERING SHAFT ASSEMBLY WITH 7/16" BOLTS. TORQUE BOLTS 63 TO 75 FOOT POUNDS.
THE FRONT AND REAR WHEEL HUB RETAINER NUTS HAVE BEEN INCORRECTLY TORQUED. THE PRELOAD ON THE BEARING FROM THE LOOSENED HUB RETAINER NUT MAY CAUSE BEARING FAILURE.
A WHEEL BEARING FAILURE MAY CAUSE THE AXLE TO BREAK,RESULTING IN LOSS OF VEHICLE CONTROL AND POSSIBLE VEHICLE ACCIDENT.
INSPECT BEARING AND REPLACE IF NECESSARY. TORQUE THE HUB RETAINER NUT 230 TO 350 FOOT POUNDS.
THE HORN ACTIVATING SWITCH COMPONENTS LOCATED IN THE STEERING COLUMN CAN WEAR ABNORMALLY.
THE HORN MAY BE ENERGIZED AND SOUND CONSTANTLY, OR NOTENERGIZE AND FAIL. THIS COULD LEAD TO AN INABILTY TO WARN OTHER DRIVERS INA CRASH SITUATION, AND RESULT IN VEHICLE DAMAGE AND INCREASED RISK OF INJURY.
REPLACE THE STEERING WHEEL HUB AND HORN BRUSH. ARRANGE THE PARTS TO AVOID THE PREMATURE WEAR CONDITIONS.
THE LOWER BALL JOINT RETAINING NUT THAT HOLDS THE LOWER BALL JOINT TO THE STEERING KNUCKLE WAS NOT TORQUED CORRECTLY.
IF THE LOWER BALL JOINT BECOMES DISCONNECTED FROM THESTEERING KNUCKLE, THE WHEEL WILL TIP OUTWARD RESULTING IN LOSS OF STEERINGCONTROL AND A POSSIBLE VEHICLE ACCIDENT.
INSPECT LOWER BALL JOINTS, REPLACE WORN PARTS, AND TORQUE THE LOWER BALL JOINT MOUNTING NUT 130 TO 150 FOOT POUNDS.
Recall, complaint, and investigation records from official NHTSA datasets (FLAT_RCL, FLAT_CMPL, FLAT_INV), synced weekly. Counts reflect NHTSA records for the 1990 Winnebago Cw822fw as of July 20, 2026. Complaint narratives are consumer-submitted and unverified. This page contains ads and affiliate links. Full methodology.